The safest way to use a pot without drainage holes is as a cover pot. Keep the plant in a plastic nursery pot that has holes, and set that inside the pot you like. Lift the inner pot out to water, let it drain, and put it back.
You can also drill a hole, or plant straight into the pot and water with great care. Planting straight in is the riskiest choice, since extra water has nowhere to go.
I earn a commission when you buy through links to Amazon. It costs you nothing extra.
Why drainage holes matter
Roots need air as well as water. In a pot with a hole, extra water runs out and air follows it into the soil. In a pot with no hole, extra water pools at the bottom. The soil there stays soaked, air cannot get in, and roots rot.
The trouble is that you cannot see it. The top of the soil looks dry while the bottom is soaked. By the time the plant wilts or yellows, the roots are already damaged. See what causes root rot in houseplants and how to fix it.
Option 1: use it as a cover pot
This is the best method. A cover pot is also called a cachepot.
- Keep the plant in a plastic nursery pot with drainage holes. If it needs a new one, plastic nursery pots with drainage holes from Amazon come in sets of several sizes.
- Choose a cover pot that is 1 to 3 cm (1/2 to 1 in) wider than the nursery pot, and a little taller so the plastic rim does not show.
- Set the nursery pot inside.
- When it is time to water, lift the nursery pot out and take it to the sink.
- Water until it runs from the bottom. Let it drain for 15 to 30 minutes.
- Put it back in the cover pot.
If the plant is too heavy to lift, water it in place with a small amount. After 30 minutes, tip the cover pot or lift the inner pot and pour out any water that has collected. Do not let the nursery pot stand in water.
If the cover pot is too deep, set an upturned saucer or a few flat stones in the bottom to raise the inner pot. This also keeps the roots above any drips.
Option 2: drill a hole
Many pots can be drilled. This turns the pot into a normal one.
What you need
- A power drill
- A diamond-tipped hole bit for glazed ceramic, porcelain, or glass, or a masonry bit for unglazed terracotta or concrete. A diamond hole saw drill bit for ceramic in the 6 to 12 mm (1/4 to 1/2 in) range suits most pots.
- Masking tape
- Water
- Safety glasses
- An old towel
Steps
- Put on safety glasses.
- Turn the pot upside down on a folded towel so it cannot slide.
- Stick a piece of masking tape on the spot to drill. The tape stops the bit from skating.
- Wet the spot. Keep it wet the whole time, since water cools the bit and the pot.
- Set the drill to normal mode, not hammer mode.
- Start slowly, with the bit at a slight angle, until it bites. Then bring the drill upright.
- Use light pressure. Let the bit grind through. Do not push.
- Ease off as the bit breaks through, so the inside does not chip.
- Rinse the pot.
One hole about 1 cm (1/2 in) wide is enough for a small pot. Large pots do better with three.
There is always some risk that a pot cracks. Do not drill one you cannot bear to lose. Use a saucer under any pot you drill, and see how to stop plant pots from leaking on floors and furniture.
Option 3: plant straight into the pot
Do this only if the first two will not work. It can be done, but it leaves no room for mistakes.
Rules for a pot with no hole
- Choose a small pot. Small pots dry faster. A large pot with no hole is hard to manage.
- Use a fast-draining mix. Add extra perlite or pumice, about half mix and half perlite.
- Measure the water. Do not pour until you see it pool. As a starting point, use a volume of water equal to about one quarter of the pot’s volume. A pot that holds 1 L (about 1 qt) gets 250 mL (1 cup).
- Wait longer between waterings. Let the soil dry at least halfway down for leafy plants, and all the way down for succulents.
- Check the bottom, not the top. Push a wooden skewer or a moisture meter to the bottom of the pot. If the skewer comes out dark and damp, wait. See how to use a moisture meter for indoor plants.
- Pour out extra water. If you gave too much, hold the soil in with your hand, tip the pot on its side over the sink, and let the water run out.
- Keep it in good light. A plant in bright light drinks faster and dries the pot sooner.
Do not rely on a gravel layer
A layer of stones in the bottom is common advice. It does not work the way people hope. Water does not move from fine soil into coarse gravel until the soil above is soaked. The wet zone sits higher in the pot, closer to the roots, and the stones take up space roots could use.
A gravel layer does give a small space for extra water to sit. That buys a little margin for one heavy pour. It does not replace a hole.
Plants that cope best without a hole
No plant prefers a pot with no hole. Some forgive it more than others.
| Plant | Why it copes | Pet safe |
|---|---|---|
| Lucky bamboo | Grows in plain water | No |
| Pothos | Tolerates wet soil better than most, and grows in water | No |
| Spider plant | Thick roots store water, so it needs little | Yes |
“No” means toxic to cats and dogs. Chewing the plant can cause mouth irritation, drooling, or vomiting. Call your vet or a pet poison line if a pet eats one.
Plants to keep out of pots with no hole: cacti, succulents, snake plant, ZZ plant, and orchids. They rot fast in wet soil.
You can also skip soil. A sealed pot is a fine container for a plant grown in water or clay pebbles. See how to grow indoor plants without soil.
Signs the pot is holding too much water
- Soil still wet a week or more after watering
- A sour or swampy smell
- Yellow lower leaves
- Wilting in damp soil
- Fungus gnats
- Soft, dark stems at the soil line
If you see these, slide the plant out. Cut off brown, soft roots. Replant in fresh, dry mix in a pot with a hole, and use the old pot as a cover pot.
What to do next
- Check every pot you own for a hole.
- For pots without one, put the plant in a nursery pot and use the nice pot as a cover.
- Drill pots you want to plant into directly.
For help with size and material, see how to choose the right pot for a houseplant.